designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print 2.5 .10 10.2 .40 3.1 .12 recommended cable stripping sub-sma-j-c-x-st-sb3 fig.1 sma-j-c-x-st-SR3 shown sma-j-c-x-st-bh3-cbdy sma-ins-016 sma-pin-006-x sma-lwas-001-x sma-nut-001-x sma-gkt-002 sma-j-c-x-st-SR3 gender -j: jack type -c: cable plating specification -h: heavy gold (see notes 7 & 8) (sma-nut-001-f) (sma-lwas-001-f) (sma-pin-006-h) (sma-ins-016) (sma-j-c-f-st-bh3-cbdy) (sub-sma-j-c-f-st-sb3) termination -SR3: sealed reverse polarity bulkhead (mh081) orientation -st: straight 6.60 .260 6.10 .240 2.80 .110 recommended panel cutout 3.80[.150] max. panel thickness c sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: sma str jack s rev polarity bulkhead, mh081- 50 ohm by: sma-j-c-x-st-SR3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 04/21/2009 3 1 sheet scale: 3:1 f:\dwg\misc\mktg\sma-j-c-x-st-SR3-mkt.slddrw notes: 1. represents a critical dimension. 2. center contact pushout force = 26.69 n [6 lb] min. 3. see sheet 3 for termination information. 4. components to be shipped unassembled. 5. sample orders: to be packaged in individual kit form, production orders: each component to be bulk packaged. 6. rohs compliant. 7. plating: -f: .000003" min gold over .000050" min nickel. -h: .000030" min gold over .000050" min nickel. 8. assembly plating designations: -h: (center contact)-h (outer contact) -f (remaining metal parts) -f shell,ferrule,nut,washer: brass contact: brass dielectric: ptfe gasket: silicon 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision c
0.40 ref .0157 12.35 ref .486 0.92 ref .036 1.27 ref .050 scale 8:1 10.15 ref .400 6.50 ref .256 0.50 ref .020 8.00 (hex) ref .315 9.24 ref .364 12.60 ref .496 6.33 ref .249 15.60 .614 1/4-36 uns-2a ref 5.86 ref .231 11.00 (hex) ref .433 12.70 ref .500 2.00 ref .079 1/4-36 uns-2b ref 9.90 .390 ref 6.50 .256 ref 1.70 .067 ref 1.60 .063 ref scale 8:1 0.50 .020 ref 0.65 ref .026 4.00 .157 ref 3.27 ref .129 0.75 .030 ref 6.77 ref .267 sheet of sma str jack s rev polarity bulkhead, mh081- 50 ohm by: sma-j-c-x-st-SR3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 04/21/2009 3 2 sheet scale: 2:1 revision c f:\dwg\misc\mktg\sma-j-c-x-st-SR3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
2.5 ref .10 10.2 ref .40 3.1 ref .12 mh-081 cable 7.0 2.5 .28 .10 hst-0.125-02-blk-a sma-ins-016 sma-j-c-x-st-bh3-cbdy 19.10 0.10 .752 .004 0.6 max. gap allowable .03 sma-lwas-001-x sma-nut-001-x apply heat shrink tubing sma-gkt-002 0.10 max. gap allowable .004 sma-pin-006-x c 2.30 - 0.10 0.00 (to center contact) .091 - .004 + .000 sub-sma-j-c-x-st-sb3 c reference plane 0.05 ref .002 (to insulator) detail 'a' scale 8 : 1 reference plane strip and tin inner & outer conductor add heat shrink tube, rear threaded body, and insulator solder shield solder signal pin and apply loctite 680 to threads add sub-sma-j-c-x-st-sb3 & tighten rear-threaded body to 10 in-lbs (use fixture as required to assure center contact pin location) sheet of sma str jack s rev polarity bulkhead, mh081- 50 ohm by: sma-j-c-x-st-SR3 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 04/21/2009 3 3 sheet scale: 1.5:1 revision c f:\dwg\misc\mktg\sma-j-c-x-st-SR3-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
